Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Kitchen Remodeling: The Miami Owner’s Guide
Therma-Tru makes entry and interior door systems, not kitchen cabinetry, so “Therma-Tru kitchen remodeling” in Miami almost always means one thing: a failed door component on a Therma-Tru door that sits in or near your kitchen – a patio door, a pantry door, a refrigerator surround door – and you need it matched, priced, and reinstalled so the kitchen project can move forward. A full kitchen remodel in Miami runs $16,520 – $53,100 installed, and door repair or replacement done within that scope is typically folded into the project rather than billed as a separate line. We don’t claim same-day service on planned kitchen work – nobody remodels a kitchen in a day, and we won’t pretend otherwise.

Owners usually discover the problem the slow way. The patio door starts dragging on the threshold in July. The pantry door no longer latches after a humid stretch. A sidelight seal lets water past the frame and the drywall beside the kitchen counter stains. By the time it’s obvious, the door has been out of spec for a season or more, and the kitchen schedule is already set.
Which Therma-Tru Models This Applies To
Therma-Tru door lines most often found in Miami kitchens and adjacent spaces include the Fiber-Classic, Smooth-Star, and Classic-Craft series for entry and patio doors, plus the Benchmark and Profiles lines for interior doors. Hinges, locksets, multipoint hardware, sills, sweeps, and weatherstrip are series-specific, and the right part depends on the door slab thickness, the frame system, and the handing (left or right). Getting this wrong is the single most common failure we see on Therma-Tru work in Miami: a homeowner orders a hinge or sweep that fits a 1¾-inch Smooth-Star and it won’t seat on a Classic-Craft frame that’s built to a different tolerance.
Before you buy anything, find the label. Therma-Tru applies a model and series sticker to the hinge-side jamb, and it’s often painted over. Wipe it with a rag and a little mineral spirits; if it’s gone, measure the slab width and height to the nearest 1/16 inch, measure the jamb depth, and note whether the door is inswing or outswing. That’s the minimum information any supplier needs to match a part.
OEM versus aftermarket is a real decision on Therma-Tru specifically. OEM hardware fits the first time and holds the manufacturer’s tolerances, but costs more and can take longer to source. Quality aftermarket equivalents – brands that spec to Therma-Tru dimensions – are cheaper and faster, and are fine for sweeps, weatherstrip, and standard hinges. For multipoint locks, sills, and anything structural, we go OEM on Therma-Tru every time, because aftermarket tolerance drift shows up as a door that leaks air in Miami’s summer humidity within a year or two.
One note on who we are: Groundwork Construction Co. of Miami is an independent service provider. We’re not affiliated with Therma-Tru, and we don’t claim to be. We work with the product because it’s what’s in your home.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Therma-Tru Kitchen Remodeling Is Failing
- The door drags or rubs the threshold. Usually a failed hinge, a sagging hinge jamb, or a swollen slab from moisture intrusion. In Miami’s humidity, a slab that’s taking on water swells and never fully recovers, so a simple hinge swap won’t fix it – the water source has to be found.
- Daylight or water visible around the door edge. That’s weatherstrip or sweep failure, or a frame that’s out of square. Both let Miami’s afternoon rain and air conditioning differential drive moisture into the wall cavity.
- The lockset or multipoint won’t engage smoothly. Hardware misalignment or a worn strike. Left alone, this is what strips the lock cylinder and forces a full hardware replacement instead of a $40 part.
- The sill is soft, cracked, or discolored. Sill rot is the deepest failure on a Therma-Tru door in South Florida. It’s the part that traps water, and it’s the part most owners never look at until the adjacent kitchen drywall is already damaged.
- The door won’t stay closed or won’t latch at all. Warped slab or a settled frame. This is the point where the kitchen project schedule gets pushed, because the door has to be corrected before cabinets and counters go in around it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Because Therma-Tru doesn’t make kitchen cabinetry, there’s no honest “Therma-Tru part price” for a kitchen – the number that matters is the installed kitchen remodel range in Miami: $16,520 – $53,100 for a full remodel, $10,620 – $23,600 for a small kitchen remodel. If your Therma-Tru door needs work within that project, hinge and hardware swaps, sweeps, and weatherstrip run at the low end of the labor line; sill replacement and frame correction cost more because they involve trim removal and finishing.
What drives the range in Miami specifically: cabinet and counter selection, whether the layout changes, permit requirements for anything structural, and how much door and frame correction the existing opening needs. We price it line by line before work starts, and the number you see is the number you pay. Every project is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. We also pull the permits and pass the inspections, and we’ll handle KraftMaid cabinetry, Cambria or Silestone counters, and the door work in one scope so you’re not coordinating three trades.
DIY or Call Us?
You can safely check a few things yourself: wipe the jamb label and write down the model, measure the slab, look for daylight at the edges on a sunny afternoon, and press a screwdriver into the sill to see if it’s soft. That’s diagnosis, not repair, and it costs nothing.
Where DIY goes wrong on Therma-Tru is the sill and the frame. Replacing a sill means cutting out the old one without damaging the slab or the rough opening, then re-flashing so water sheds away from the kitchen wall – and in Miami, a sill that’s flashed wrong looks fine for one dry season and fails the first time a tropical system parks over Dade County. We’ve seen homeowners turn a $200 sill job into a $4,000 drywall and cabinet repair by getting the flashing wrong. If the door drags, the sill is soft, or water is getting in, that’s a professional call. Call (833) 968-1198 and we’ll walk you through what’s actually needed before you spend anything.
FAQs
Hardware and weatherstrip typically last 8 – 12 years in South Florida, and sills last 10 – 15 depending on sun exposure – noticeably shorter than the 20-year figures quoted for northern climates, because Miami’s humidity and UV load accelerate seal and sill degradation. Sills facing west or south take the worst of it. Call (833) 968-1198 for an exact assessment – estimates are free.
Often yes – hinges, strikes, sweeps, and weatherstrip are usually repairable or swappable without touching the door, and multipoint hardware can frequently be adjusted back into alignment. A soft or cracked sill is the exception; it gets replaced, not patched, because a patch traps water. We’ll tell you honestly which one you’re looking at. Call (833) 968-1198 for a free estimate.
Hardware, weatherstrip, and sweep work is typically finished in a single visit of a few hours. Sill replacement and frame correction run longer – usually a full day plus finish work – and those get scheduled into the kitchen project timeline so cabinets and counters aren’t delayed. Call (833) 968-1198 to get it on the calendar.
We match the part to your door’s series, slab dimensions, handing, and frame system using the jamb label and physical measurements, then source OEM hardware for structural components and quality aftermarket equivalents only where we’ve verified the tolerances hold. We don’t claim to stock Therma-Tru parts – no contractor carries that inventory – so lead time depends on the part. We’ll tell you the lead time upfront. Call (833) 968-1198 to start.
Whether your kitchen project is a full remodel or a single failing door that’s holding up the schedule, the next step is the same: a free estimate with real numbers and no surprises. Our technicians have up to 12 years of experience, every technician is background-checked and arrives in uniform, and calls are answered by a live person 24/7 – no voicemail, no waiting until Monday. Groundwork Construction Co. of Miami handles kitchen remodeling from foundation to finish line, backed in writing by the 730-Day Done Right Promise. We also offer $1,000 off projects over $10,000 and 0% financing for 18 months. Call (833) 968-1198 for your free project estimate and design consult.
Written by the team at Groundwork Construction Co. of Miami, serving Miami and nearby areas.