Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Miami Owner’s Guide
Barrette kitchen remodeling in Miami runs $16,520 to $53,100 installed, depending on cabinet run length, countertop material, and whether the layout changes. That’s a full kitchen scope: Barrette cabinetry, countertops, backsplash, and island work planned as one project with one crew and one written quote. Most Barrette kitchen projects here are planned and scheduled rather than done same-day, because the work is a remodel, not a repair. Our technicians have up to 12 years of experience, so we can tell you before you commit what your specific Miami kitchen needs.

Miami owners usually figure this out in stages. First, a Barrette cabinet door stops closing flush. Then the soft-close hinge lets go when you bump it. Then you pull a drawer and hear the runner grinding on one side. You start looking for the part and find that Barrette’s cabinet hardware follows its own sizing, not the generic hardware bins at a big-box store. Add Miami’s humidity, and the failure clock speeds up. This page covers what fails, which hardware matches your Barrette series, and what replacement and remodel work really cost in Miami.
Which Barrette Models This Applies To
Barrette makes a wide cabinet lineup, and the hardware is not universal across it. The first job is matching the part. Most Miami Barrette installations we open up fall into a few families: framed construction, frameless full-overlay, and rigid thermofoil or laminate fronts that show up in condos and rental turns. The hardware you need is determined by which of those you have, not by the color of the door.
Here’s how to identify your kitchen without guessing. Open a base cabinet and look at the door back. Are there face-frame rails around the opening (framed), or does the door sit on a full panel (frameless)? Measure the door overlay at the hinge side with a ruler, in millimeters. Check for a manufacturer sticker inside the sink base or on the back of a drawer box. Write down the cabinet run length and door thickness. Barrette hinge plates mount with specific screw spacing and cup-bore diameters, and mismatched plates will bolt on but won’t align with the factory door holes.
Then the OEM question. Genuine Barrette parts match the original fit and finish, which matters most on visible hinge plates and drawer glides. Quality aftermarket European-style hinges and full-extension glides fit the same cup patterns on most frameless runs and cost less, but the fit tolerance varies by brand. On a Barrette framed cabinet with exposed hinges, aftermarket replacements often look wrong before they function wrong. We compare your hardware to the original spec, tell you which route makes sense, and source it. Groundwork Construction Co. of Miami is an independent contractor and not affiliated with Barrette, so we’re not locked into one brand.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Kitchen Remodeling Is Failing
- Doors that swing past their stop. The hinge’s spring or stop tab has worn out from years of opening. On Barrette frameless cabinets, a tired hinge lets the door ride over the carcass and chip the face.
- Soft-close drawers that slam. The damper in the glide has dried out and released. In Miami’s humidity, these dampers fail faster than in dry climates because the plastic absorbs moisture and hardens.
- Drawer boxes that sag or rub the frame. One of the two glide runners has pulled loose or the roller has worn flat. Keep pulling the drawer, and the box will crack at the corner joint.
- Lifting or bubbling door fronts. On thermofoil and laminate fronts, moisture from above-sink steam gets under the edge and the skin lifts. Miami kitchens see this most on the cabinet beside the sink and above the stove.
- Cracked or delaminating countertop edges. Barrette-adjacent countertops that fail at the seam or backsplash joint usually trace back to movement under the cabinet run. The top isn’t the problem; the cabinet face it sits on has shifted.
One Florida note: our salt air and summer humidity cause steel hinges, screws, and slides to pit and rust faster than they would inland. If you see rust streaks inside a Barrette cabinet, the hardware is nearing the end of its life even if the door still works.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Barrette kitchen remodeling in Miami is priced in layers. Here’s how the ranges stack up, so you know what you’re actually paying for:
| Scope | Installed Range |
|---|---|
| Full kitchen remodel | $16,520 – $53,100 |
| Small kitchen remodel | $10,620 – $23,600 |
| Cabinet installation | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
What drives the range: cabinet run length and door count, material choice (thermofoil versus solid wood versus laminate), countertop surface (Cambria quartz and Silestone run higher than laminate), and whether plumbing or gas lines get moved. If you’re only setting a failed drawer glide or hinge, that’s a targeted repair, and we’ll quote it honestly instead of up-selling a full kitchen. Every quote is line-item and fixed, with no change orders, and the work carries our 730-Day Done Right Promise. A Barrette cabinetry partner we also work with is KraftMaid if you’re weighing a full cabinet replacement.
DIY or Call Us?
Some of this an owner can safely check. Confirming your cabinet type, measuring the overlay, writing down the sticker number inside the sink base, and photographing the hinge or glide are all fine to do yourself. That gives us a fast, accurate match.
Where DIY goes wrong: swapping hinges on a frameless Barrette run without checking the cup-bore and screw spacing means the new plate bolts on but pulls the door out of alignment. You end up re-drilling cabinet faces and chasing the original factory line. Replacing one glide without checking the mating runner leaves the drawer rubbing, and the box cracks. On laminate or thermofoil fronts, an owner who pries a water-swollen edge usually takes half the laminate with it. That’s when the part costs more to fix than calling.
We’ll match the number, tell you honestly whether a part fix or a remodel makes sense, and answer the phone live at 24/7. Call (833) 968-1198 to schedule your free estimate.
FAQs
Expect 8 to 12 years on soft-close hinges and glides in a south Florida kitchen, shorter near the sink and stove where moisture is constant. Salt air and humidity speed corrosion on steel parts, so inland owners may get a few more years. Call (833) 968-1198 for an exact quote – estimates are free.
Sometimes yes. A single hinge or glide swap is a targeted repair and costs a fraction of a remodel, and we’ll say so. But if the hinge plates are pitting or a drawer box has cracked at the joint, a repair just delays the failure. Call (833) 968-1198 for an exact quote – estimates are free.
A hinge or glide replacement is usually a single-visit job, while a full cabinet or countertop install runs a multi-day scheduled project. We plan the work around your kitchen and tell you the timeline in the written quote. Call (833) 968-1198 for an exact quote – estimates are free.
We identify your cabinet series from the sticker or carcass type, match the hardware by overlay and cup-bore measurement, then compare genuine Barrette parts against quality aftermarket equivalents. You get one line-item quote for the part and the labor, not a bill that changes mid-job. Call (833) 968-1198 for an exact quote – estimates are free.
Written by the team at Groundwork Construction Co. of Miami, serving Miami and nearby areas.