Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Toto Bathroom Remodeling: The Miami Owner’s Guide
Bathroom remodeling with Toto fixtures in Miami typically runs $10,620 to $33,040 installed, and most of that spread comes down to which Toto pieces you keep, which you replace, and how far the tile work reaches. When a Toto toilet starts ghost-flushing at 2 a.m., or a Toto washlet seat stops warming, the failure is almost always a fill valve, a flush tower gasket, or a control board inside the bidet seat rather than the porcelain itself. We install Toto-compatible bathroom remodels across Miami, and we can usually schedule a free estimate within a few days. Groundwork Construction Co. of Miami is an independent service provider and is not affiliated with Toto.

Key Takeaways
- Toto fill valves and flush tower gaskets fail on a predictable schedule in South Florida’s hard water, often in the 3 to 7 year window.
- Replacing a valve, gasket, or washlet control board costs a fraction of a full remodel and keeps the fixture you already paid for.
- If you’re redoing the whole bathroom, Toto’s rough-in dimensions and seat height matter before the tile goes down, not after.
- Your full project is covered by the 730-Day Done Right Promise, in writing.
Which Toto Models This Applies To
Toto’s residential line splits into a few families that matter for parts. The Drake, Eco Drake, and Ultramax use the G-Max or E-Max flush system with a replaceable fill valve and a silicone flapper or flush tower gasket. The Aquia and Vespin II use a dual-flush tower with its own gasket set. The Washlet and S7/S5/SX series bidet seats are a whole separate parts ecosystem: control board, seat heater, water heater, pump, and nozzle assembly all wear independently. The Neorest integrated toilets combine the two, and a Neorest repair is where owners most often face a $600-plus service call because everything is dealer-sourced.
Identifying the right part means reading the model tag, not guessing. Toto stamps the model number inside the tank lid underside and on a label behind the bowl. Write down the full alphanumeric code (for example, CST776CEFG or SW3084T40) and measure the tank’s inside width and the fill valve height before you buy. The compatibility gotcha that trips up Miami owners: Toto changed the G-Max fill valve shaft length between older and newer production runs, and a generic Fluidmaster valve will physically fit but sit too tall or too short, causing weak refill or an endless run. On the aftermarket question, we lean OEM for Toto fill valves, flush tower gaskets, and Washlet boards because the fit and the internal electronics calibration are brand-specific. Quality aftermarket flappers are a reasonable substitute on older Drakes. We don’t stock parts and don’t carry them on a truck; we source from Toto’s distribution and match the exact model code on your tag.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Toto Bathroom Remodeling Is Failing
- Ghost flushing or a toilet that refills on its own. A worn flapper or flush tower gasket lets tank water seep into the bowl slowly, and the fill valve cycles to top it off. In Miami’s hard, mineral-heavy water, that rubber seals and dries faster than in softer-water markets.
- Weak flush or swirling without clearing. This usually points to a failing fill valve that isn’t refilling the tank to the right level, or mineral buildup in the rim jets. Toto’s rim wash holes clog more readily in areas on well water or older municipal lines.
- Washlet seat not heating, water not warming, or nozzle stuck. The seat heater element or the water heater inside the bidet seat has failed, or the control board has moisture damage. Miami’s humidity and bathroom steam accelerate corrosion on those boards.
- Water pooling at the base of the toilet. A failed wax ring or a cracked outlet, not a parts problem. This one needs the fixture pulled and reset, and any soft subfloor around it checked before new flooring goes in.
- Constant running and a rising water bill. The fill valve has failed open. Shut the angle stop behind the toilet and stop using it until the valve is replaced, because a running toilet can waste hundreds of gallons a day.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A Toto fill valve replacement typically runs $120 to $260 installed, a flush tower gasket $90 to $180, and a Washlet control board swap $220 to $480 depending on the model and part lead time. Those are parts-plus-labor, transparent, with the number you see being the number you pay. A full bathroom remodel with Toto fixtures kept in place or upgraded lands in our lead range of $10,620 to $33,040 for Miami, driven by tile scope, vanity and shower work, and whether the Toto suite is preserved or replaced. A small bathroom remodel runs $5,900 to $14,160, and a bathroom vanity installation alone is $945 to $3,540.
What pushes cost up: hard-water scale damage that requires flushing the lines, a Neorest integrated unit needing dealer-sourced electronics, and any subfloor repair behind a leak. What keeps it down: keeping your existing Toto toilet and just renewing the valve and gasket while the room around it gets finished. Every install and remodel is covered by the 730-Day Done Right Promise, so if a valve we set leaks or a seat we wired fails inside that window, we come back and make it right. We also offer 0% financing for 18 months and $1,000 off projects over $10,000, and the estimate and design consult are free.
DIY or Call Us?
Here’s the honest split. You can safely check the tank for a slow leak by adding a few drops of food coloring and watching the bowl for 15 minutes without flushing. You can read your model tag, shut the angle stop, and remove the tank lid to look at the valve. That’s diagnosis, and it’s worth doing.
Where DIY goes wrong on Toto: the fill valve and flush tower gasket are matched to the tank by height and diameter, and the wrong part causes weak flushes or a slow leak that rots the subfloor, a genuinely expensive mistake in a Miami home where that subfloor sits over a slab or a second-story ceiling. The Washlet boards carry line voltage into a wet environment, and a mis-wired heater is a shock and fire risk, so that part goes to a trained technician. We send background-checked, uniformed technicians, and our calls are answered by a live person 24 hours a day. Call (833) 968-1198 to schedule your free estimate and we’ll tell you what part you need and what it will cost before we touch anything.
FAQs
Toto fill valves typically last 3 to 7 years in Miami, shorter than the manufacturer’s stated life because our hard, mineral-heavy water wears rubber seals faster, and the coastal humidity accelerates corrosion on Washlet control boards. If your valve is past five years and the toilet has started cycling on its own, plan for replacement. Call (833) 968-1198 and we’ll give you an exact quote, free.
Sometimes, yes. A flush tower gasket or flapper can be swapped on its own for a fraction of what a full valve assembly costs, and a Washlet nozzle assembly can often be cleaned or replaced without touching the control board. What usually can’t be repaired is a burned-out seat heater or a cracked control board; those require replacement. We’ll tell you which you’re looking at, honestly, before you commit.
A fill valve or gasket replacement is a same-visit job, usually 30 to 60 minutes from shutoff to test flush. A Washlet control board swap runs a bit longer depending on model and how much you want tested, and if the part has to be sourced from Toto’s distribution, we’ll schedule the install around that lead time. We confirm the model code up front so we’re not making a second trip for the wrong part.
We match the exact model code from your tank tag or Washlet label and order through Toto’s distribution network, which is why reading that code first matters. We don’t keep parts in stock or on a truck; every part is ordered to your model, so what arrives fits. That also means we’re not selling you a generic valve that “usually works.” Call (833) 968-1198 with your model number and we’ll price it.
If your Toto fixture is failing or you’re planning a Miami bathroom remodel around Toto pieces you already trust, get a straight answer and a fixed price before any work starts. We also service KraftMaid, Cambria, and Silestone in our kitchen and bath work, and we’re happy to quote those alongside the bathroom scope. Call (833) 968-1198 for your free estimate and design consult. Upfront pricing, no surprises, and the 730-Day Done Right Promise standing behind every job.
Written by the team at Groundwork Construction Co. of Miami, serving Miami and nearby areas.