Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tile Roofing in Gladeview, FL: What the Job Actually Involves
Tile roofing in Gladeview runs $600 – $2,500 for a localized repair and $8,000 – $20,000 for a full tile roof replacement, with most single-slope or partial tear-offs landing in the $6,000 – $14,000 band. A typical repair is done in a day; a full replacement takes four to seven working days once the county permit is in hand. In Gladeview specifically, the work is governed by Miami-Dade’s High-Velocity Hurricane Zone rules, not a city building department, so every tile and fastener has to carry a current product approval. Call (833) 968-1198 to schedule a free on-site estimate.
How Our Tile Roofing Process Runs, Start to Finish
Tile work is unforgiving of shortcuts. Once water gets under a field tile, the underlayment is already gone and the damage shows up as a stain on a ceiling two rooms away. Here’s the sequence we follow.
Day 1: Inspection, moisture readings, and the tie-in check
We walk the roof, photograph every cracked or slipped tile, and take moisture readings in the attic decking. On Gladeview‘s mid-century concrete-block homes, this is also when we look at how the roof ties into the wall. Because so many 33147 houses have had carports closed in or rear rooms added over the decades, the tie-in is not always what the original drawings say. Finding that on day one is far cheaper than finding it during a storm.
Days 1 – 2: Tear-off and deck inspection
We remove the existing tile and underlayment down to the deck, then inspect the sheathing for rot, soft spots, and rusty fasteners. Any compromised decking gets replaced and documented. This is the stage where surprise costs live, and it’s why we photograph the deck before we cover it back up. You see the same pictures we do.
Days 2 – 3: Underlayment and flashing
New underlayment goes down first, then the flashing at valleys, penetrations, and the roof-to-wall line. Underlayment is the real waterproofing layer on a tile roof; the tile is the armor over it. We spec a wind-rated, high-temperature underlayment suited to South Florida UV, and we don’t skip the secondary water barrier where the county requires one.
Days 3 – 6: Tile setting and fastening
Field tile goes down in courses, fastened to the county’s wind-load schedule for your exposure category. Ridge and hip tiles get set in mortar with mechanical fastening where the approval calls for it. This is the slowest stretch of the job, and it’s where a crew that rushes shows up later as slipped tiles after the first summer squall.
Final day: Inspection, cleanup, and paperwork
We sweep for broken tile, run a water test on the flashed areas, and hand you the permit inspection record with the manufacturer’s material warranty. The work itself is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Tile Options You’ll Choose Between
Most of the decisions happen before day one. These are the ones that actually change the price and the lifespan:
- Clay vs. concrete tile. Concrete is the workhorse on Gladeview roofs. It costs less, holds color well, and comes in a wide range of profiles. Clay runs higher per square and is heavier, but it holds its finish longer under intense UV. For most 33147 homes, concrete is the practical call; clay suits owners chasing a specific look.
- Barrel, S-tile, or flat profile. Barrel gives the classic South Florida look and sheds water fastest. S-tile sits between barrel and flat on cost and install time. Flat profiles are the least expensive per square and the easiest to walk for future maintenance.
- Underlayment grade. This is often the biggest quality gap between bids. A premium wind-rated membrane costs more up front but is the layer that keeps your ceiling dry through a hurricane season.
- Fastener and attachment spec. The county’s wind-load schedule determines how many fasteners per tile and what type. A bid that shaves fasteners is a bid to walk away from.
- Color and finish. Standard colors cost nothing extra. Some premium finishes carry a small premium and hold their tone longer in the sun.
If you’re also updating the glazing on the same house, homeowners often pair this with Impact Windows & Doors in Gladeview so the whole envelope gets brought up to the same wind standard in one permit cycle.
What Tile Roofing Costs in Gladeview, FL
Local tile roofing runs $600 – $2,500 for repair and $8,000 – $20,000 for a full replacement. Those ranges hold for most Gladeview homes, but five variables push a job toward one end or the other:
- Roof size and pitch. Square footage drives the material cost; steep or complex pitches drive labor. A simple gable is cheaper per square than a roof with multiple valleys and hips.
- Deck condition. Soft decking or rot adds replacement cost. Mid-century homes here sometimes have sheathing that has been wet for years.
- Unpermitted additions. Extra rooms and closed-in carports mean the roof geometry changed without a permit. Verifying and correcting the tie-in adds scope.
- Tile grade and profile. Concrete flat tile sits at the low end; clay barrel sits at the high end. Underlayment grade is folded into the same decision.
- Permit and inspection scope. Because this is unincorporated county land, Miami-Dade’s product-approval and inspection requirements drive some of the cost – and the work has to pass those inspections.
A written estimate from us itemizes tile, underlayment, decking allowance, flashing, permit, and labor, with upfront pricing – the number you see is the number you pay. It does not include structural repairs discovered mid-job or landscaping damage from material staging; those get a separate written approval before anyone touches them.
See the difference
Before
After
Before
After
Before
AfterWhat Gladeview Homes Specifically Do to This Job
There is no city hall in Gladeview. That single fact reshapes the permit process. Every tile roofing job here runs through Miami-Dade County’s product-approval (NOA) system and High-Velocity Hurricane Zone rules, which means every tile, underlayment, and fastener carries a current approval number before it goes on the roof. It’s a stricter path than a neighboring city job would be, and it’s non-negotiable – you can’t pass inspection without it.
The housing stock adds the second layer. Much of the 33147 pocket around NW 79th Street is 1940s – 1960s concrete-block and terrazzo construction, with a long history of room additions, closed-in carports, and rear units added without permits. When we tear off a roof here, we’re often the first to see how those additions were tied into the original structure – and whether the tie is up to code. That’s a normal part of the work on this street grid, not an exception. County 40-year recertification and post-storm inspections surface the same unpermitted work, and the roof is usually where it shows first. If you want the bigger picture on how a full Roofing in Gladeview project fits together, including gutters and storm damage, we cover that on the city page.
Serving Gladeview, FL – Our Local Coverage Area
We serve Gladeview and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tile Roofing in Gladeview
A localized tile repair is usually a single day. A full replacement runs four to seven working days after the county permit issues, depending on roof size and weather. Call (833) 968-1198 for a timeline based on your specific roof.
Yes. Gladeview is unincorporated Miami-Dade County, so the county issues the permit and inspects the work, with wind-borne-debris-rated materials required. We pull the permit and arrange the inspections as part of the job.
Often, yes. If the deck and underlayment are sound, we can replace damaged tiles and repair localized flashing without a full tear-off. A moisture inspection on day one tells us whether partial repair is viable or whether the underlayment is already compromised.
Repairs run $600 – $2,500 and full replacements $8,000 – $20,000, with the range set by roof size, deck condition, tile grade, and permit scope. Call (833) 968-1198 for an exact quote – estimates are free.
Tiles and underlayment carry the manufacturer’s material warranty, and the labor is covered by our 730-Day Done Right Promise. We hand you the inspection record and warranty paperwork at final walkthrough.
Get a Free Tile Roofing Estimate in Gladeview
Call (833) 968-1198 to schedule a free on-site estimate for tile roofing in Gladeview. We’ll walk the roof, photograph the deck, check the tie-in, and hand you a written, itemized estimate with upfront pricing and the permit scope spelled out. Calls are answered by a live person, 24/7, and there’s no obligation to book. If you’re weighing this against a wider project, our Roofing service page covers the full scope, and you can see everything we do on the Gladeview service-area page.
Written by the team at Groundwork Construction Co. of Miami.