Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Miami, FL: What They Cost and How the Work Runs
Custom & Geometric Windows in Miami means arched, round, half-round, eyebrow, trapezoid, triangular or gable-end units built to the opening you actually have, and most jobs here run $9,440 – $29,500 once you’re into the impact-rated, Miami-Dade NOA-approved product the county requires. A single arch or radius unit ordered to size typically takes 6 to 10 weeks from template to glass, and the installation itself is usually a one- to two-day job once the frame arrives. Call (833) 968-1198 to get a free on-site estimate and a written line-item quote.
Key takeaways:
- Every custom or geometric window in Miami needs a Miami-Dade NOA number. National or Florida-only approvals don’t satisfy the county.
- Template-based measurement is standard for radius and arch units. The window is built to the template, not to a number off a tape.
- Salt air and hurricane-season UV degrade sealants and fasteners here years faster than inland, so hardware choice matters as much as the glass.
How we do a custom or geometric window job, stage by stage
Stage 1: Site visit and feasibility check. We open the wall, look at the header, and confirm what the structure will actually carry. A 6-foot half-round in a CBS wall behaves differently from the same unit in a 1920s Mediterranean Revival frame wall. We check the flat or low-slope roof line if the window sits high, because wind-driven rain at a gable end needs different flashing than a side-wall opening. You decide here whether you want one feature window or a matched set across a facade. This visit runs about 60 to 90 minutes.
Stage 2: Product selection and NOA verification. This is where the real decisions land. You choose frame material (aluminum, wood-clad, vinyl), glass package, and finish. We confirm the exact unit carries a current Miami-Dade NOA number, because the county won’t approve the permit without it and the inspector will check the label on install day. Allow one to two weeks for selection and submittal prep.
Stage 3: Permitting. Custom and geometric openings go through Miami-Dade’s product-control process. Expect two to four weeks for the permit to clear, longer if the building is in a VE or AE flood zone and elevation documentation is required. You don’t have to chase any of this. We submit and track it.
Stage 4: Template and manufacturing. For radius and arch units, a fabricator’s template is taken at the opening. Lead times run 6 to 10 weeks for custom impact glass, longer for exotic geometry or matched sets. You sign off on the shop drawing before cutting begins. This is the stage where changing your mind costs real money, so we push for final decisions before the template goes out.
Stage 5: Install, inspection, and finish. Demo and prep take a day. Setting and sealing the unit takes a day for most openings. We flash, seal, and trim to match the existing exterior. The county inspection follows, and we’re on site for it. Final walkthrough and touch-up finish the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Custom geometry narrows your product list fast, but you still have real choices to make.
- Frame material: Aluminum holds a crisp radius and takes powder-coated finishes well; it’s the common pick for geometric openings on modern and MiMo facades. Wood-clad gives you a warmer interior look and better thermal performance but costs more and needs more attention near the coast. Vinyl is the budget option and works for simple arches, though fine radius profiles can look chunky.
- Glass package: Impact-rated laminated glass is the baseline in Miami-Dade. Low-E coatings cut solar heat gain, which matters on west- and south-facing features. Tinted or reflective glass suits glassy high-rise work; clear suits residential facades where you want the geometry to read.
- Configuration: Fixed units are the norm for true geometric shapes. Operable geometric windows exist but cost more and add hardware to maintain. A matched half-round over a pair of rectangles is the classic eyebrow-and-rectangle elevation; a full circle set into a stucco wall is a stronger statement and a heavier install.
- Brand and finish: Andersen and Marvin both build to custom templates and carry product for this market. Where finish hardware or adjacent bath fixtures come into the same project scope, homeowners sometimes look at Delta or American Standard for the pieces that tie the room together.
What Custom & Geometric Windows costs in Miami, FL
Plan on $9,440 to $29,500 for this work in Miami. That’s the honest spread, and where you land inside it depends on five things.
- Size and glass area: a small eyebrow over a doorway sits near the bottom. A full-height arched feature or a matched set across a two-story facade pushes toward the top.
- Existing condition: if the opening needs reframing, new header work, or stucco repair after demo, add cost. Unreinforced masonry in older Miami stock often means structural patching before the unit goes in.
- Whether you’re relocating anything: moving a window location means moving structure, and sometimes wiring or plumbing runs inside the wall. That’s a different job from replacing an opening in place.
- Material grade: aluminum with a standard finish and laminated impact glass is the practical middle. Wood-clad with premium glazing and custom finish is the top.
- Permit and inspection scope: flood-zone documentation and wind-mitigation requirements add paperwork and, occasionally, a required upgrade elsewhere in the opening.
Your written estimate includes product, template, permitting, installation, flashing and sealing, inspection coordination, and exterior trim. It does not include interior drywall repair or paint unless we scope it in, and it doesn’t include structural repair found after demo. We put both in writing before the first cut so there’s no surprise later. If window work is part of a full Windows & Doors in Miami scope, we price it as one package.
See the difference
Before
After
Before
After
Before
AfterWhat Miami homes specifically do to this job
Miami-Dade County is the only place in the US with its own product-approval system, so a custom window here isn’t approved because it passed a national test. It’s approved because it carries a Miami-Dade NOA number, and the inspector will look for that label. In Coral Gables and Coral Terrace, where the housing stock runs to 1920s Mediterranean Revival and post-war CBS block, we routinely find openings that were never framed for a radius unit, so the header work becomes part of the job. Along Brickell and Biscayne Boulevard, the post-2000 glass towers bring a different problem: matching an existing curtain-wall profile and getting the new unit to carry the same wind-load rating as the building envelope. In Brownsville and Miami Springs, flat and low-slope roofs mean a high gable-end window needs careful flashing, because wind-driven rain in hurricane season finds every gap. Salt-laden coastal air also eats exterior sealants and fasteners faster than inland, and we build that into the material spec. If a project grows past windows into hardscape, homeowners often pair this with Concrete Driveways & Concrete Work in Miami or Asphalt Driveways & Resurfacing in Miami while the crew is already on site. We cover the whole of Miami, and our Windows & Doors service covers the wider envelope work when you want it handled under one contract.
Serving Miami, FL – Our Local Coverage Area
We serve Miami and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Custom & Geometric Windows in Miami
Expect 8 to 15 weeks end to end: 2 to 4 weeks for the permit, 6 to 10 weeks for custom fabrication, and 1 to 2 days for the install itself. Call (833) 968-1198 for a timeline tied to your specific opening – the estimate is free.
Yes. Every window in Miami-Dade County requires a permit and a unit with a current Miami-Dade NOA number. We pull the permit and coordinate the inspection; you don’t touch the paperwork. Call (833) 968-1198 to start with a free on-site assessment.
Often yes, if you’re replacing an existing opening in place or setting a geometric unit inside a wall that already carries the load. Relocating an opening or adding a new one in a CBS wall means structure work, and that changes both timeline and cost. Call (833) 968-1198 and we’ll tell you which one you have.
The range is $9,440 to $29,500 depending on size, material grade, existing condition, and permit scope. A small eyebrow arch sits near the bottom; a matched set of impact-rated feature windows sits near the top. Call (833) 968-1198 for a written line-item quote – estimates are free.
Every custom and geometric window installation is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. Manufacturer coverage on the unit itself runs separately and varies by product. Call (833) 968-1198 with questions about coverage before you commit.
Get a free estimate on custom & geometric windows in Miami
We’ll come out, measure the opening, confirm what the structure will carry, and hand you a written line-item estimate with the product, permit, and install costs separated out. No-hassle upfront pricing, no surprises. Calls are answered by a live person around the clock, and every technician who shows up is background-checked and in uniform. Call (833) 968-1198 to schedule your free estimate for Custom & Geometric Windows in Miami.
Written by the team at Groundwork Construction Co.