Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Opa-locka, FL: What You’re Getting Into
Custom & geometric windows in Opa-locka typically run $9,000 – $26,000 for a whole-house package, and a single arched or radius unit usually lands between $1,800 and $4,500 installed. That higher-than-standard figure comes from one thing: geometry. Curved heads, true arches, circle-top and half-round windows, trapezoids for gable ends, and the odd angled corner opening all require measured shop drawings, radius-matched frames, and glass cut to a template rather than pulled off a shelf. If you’ve been quoted a number that sounds like a standard double-hung job, ask what got left out. Call (833) 968-1198 and we’ll walk through your openings before anyone quotes a figure.
How the Job Actually Runs, Start to Finish
Custom window work is slower than a straight replacement because every opening is its own small project. Here’s the real sequence we work through.
Stage 1 – Site measure and drawing review (1 – 2 weeks). We measure every rough opening, check plumb and square on walls that were built in the 1920s or 1950s, and photograph what’s behind the trim wherever we can see it without opening the wall. You decide here whether each opening gets a true radius, a segmented arch, or a squared unit with a decorative head.
Stage 2 – Shop drawings and material commitment (2 – 4 weeks). Your window manufacturer produces dimensioned drawings for each unit. You sign off on frame material, glass package, and finish. Changes after this point reset the clock, so this is the signature that matters most.
Stage 3 – Fabrication (5 – 10 weeks, longer for radius and true-arch units). Arched and circular windows are built to order. A rectangle ships faster; a true half-round with a matched radius does not. We give you a fabrication window in writing rather than a vague “six to eight weeks.”
Stage 4 – Permitting and inspection. Window replacement on a wall in a wind-borne debris region needs a permit and an inspection, and curved units in older walls sometimes trigger a framing review. We pull the permit and confirm the scope before any material is ordered, not after.
Stage 5 – Installation and finish-out (2 – 5 days depending on count). Old units come out, framing is shimmed and squared, new units are anchored and sealed, and the interior trim and exterior stucco patch get finished. Stucco patching around a curved head is the step most crews rush. We don’t, because that’s where water gets in later.
Want the wider picture of how this fits a whole exterior scope? It’s often part of a full Windows & Doors in Opa-locka project, and we scale the work to match.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Frame material. Vinyl is the budget path and holds up fine on straight units, but vinyl is hard to bend and usually can’t hold a true radius, so geometry pushes you toward aluminum or wood-clad. Aluminum takes sharp curves and holds paint well in sun. Wood-clad gives you the warm interior look and the most design flexibility, at the highest cost per unit.
- Glass package. In South Florida, impact-rated laminated glass is the standard choice and also drives your insurance picture. Low-E coatings help with the intense sun here; the trade-off is a slightly cooler unit that can fog on the outside in humid mornings. That’s normal, not a defect.
- Geometry itself. A true arch cut from a single radius template looks best and costs most. A segmented arch made from short straight segments reads as a curve from the curb and saves money. A squared window with a decorative head is the cheapest route and the least fussy to seal.
- Finish and hardware. Powder-coated aluminum finishes hold color through Florida sun. Painted wood needs re-coating on a schedule. Ask what warranty each finish carries before you commit.
We keep a curated set of brand partners across the exterior trades, and on the window side that includes well-proven names we’ve specified on hundreds of units. We’ll tell you which units suit a true radius and which don’t, honestly.
What Custom & Geometric Windows Cost in Opa-locka, FL
Plan for $9,000 – $26,000 on a whole-house custom and geometric package, and roughly $1,800 – $4,500 per individual arched or radius unit installed. A single decorative gable or half-round window lands at the low end of the per-unit range; a true-arch bank of three on a front elevation lands at the high end.
Here’s what pushes a job toward the top of that range:
- Count and complexity. One curve is a nice detail; eight curves across a facade is a fabrication project.
- Wall condition. Lath, old stucco, and non-standard framing turn a swap into a rebuild of the opening.
- Glass spec. Impact-rated and specialty glass cost more than standard double-pane.
- Framing changes. Resizing an opening to take a wider arch means structural work and engineering review.
- Permit and inspection scope. A simple replacement permit is one thing; a scope that touches structure adds review time and cost.
A written estimate from us lists each unit by size, glass spec, frame material, and finishing line, so the number you see is the number you pay. We don’t do change orders that appear after the truck leaves. Ask about our 0% financing for 18 months and the $1,000 off projects over $10,000 while you’re budgeting.
See the difference
Before
After
Before
After
Before
AfterWhat Opa-locka Homes Specifically Do to This Job
Opa-locka isn’t a blank slab of new construction. The city holds the largest collection of Moorish Revival architecture in the Western Hemisphere, a 1926 themed development of domed roofs, arched openings, and ornate stucco, and that heritage shapes every custom window job here. On the original Opa-locka Company buildings along Ali Baba Avenue and Sharazad Boulevard, the openings are frequently true arches cut into load-bearing masonry, and what’s behind the stucco rarely matches modern drawings. We’ve opened walls and found 1920s framing with no modern anchors, which means an engineering review before any structural change. In the surrounding blocks of 1920s – 1950s stucco-over-block homes, original wood-frame windows have often swelled, rotted, or been patched so many times that the rough opening is no longer square, and a curved replacement has to be templated to what’s actually there rather than to a plan. Wind-driven summer rain and hurricane-season gusts also mean every unit we set has to be anchored and sealed to a real standard, not just caulked and caulked again. We work this honestly across Opa-locka and the surrounding neighborhoods, and if you’re pairing window work with exterior flatwork, homeowners often pair this with Concrete Driveways & Concrete Work in Opa-locka.
Serving Opa-locka, FL – Our Local Coverage Area
We serve Opa-locka and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Custom & Geometric Windows in Opa-locka
From signed drawings to finished install, expect 8 – 16 weeks, with the fabrication window running 5 – 10 weeks for radius units. Straight-line units move faster; true arches and matched-radius banks go to the long end. Call (833) 968-1198 and we’ll give you a real timeline for your openings.
Yes, window replacement on a wall in this wind-borne debris region requires a permit and an inspection, and we pull it as part of the job. We confirm the scope with the building department before material is ordered, so nothing gets installed that can’t pass. Ask us to walk you through the permit step on your free estimate call.
In most cases, yes, if the new unit fits the existing opening and the framing checks out. The job turns structural when you want a wider or taller arch than the wall was cut for, or when we find non-standard 1920s framing that needs anchoring. We tell you which category you’re in before you sign.
Plan for $1,800 – $4,500 installed per unit, depending on size, glass spec, and frame material. A simple squared window with a decorative head is at the low end; a true-radius unit in wood-clad at the high end. Call (833) 968-1198 for an exact quote, and the estimate is free.
Your window units carry the manufacturer’s warranty, and the workmanship on the installation is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. We put both in writing so the coverage isn’t a verbal promise.
Ready to Price Custom & Geometric Windows in Opa-locka?
We’ll come out, measure your openings, and talk through arch styles and glass specs on site. You get a written, line-item estimate for the custom & geometric windows in Opa-locka, with a real install timeline, before any commitment. Our technicians have up to 12 years of experience, every crew is background-checked and uniformed, and calls are answered by a live person 24/7. Call (833) 968-1198 for your free estimate. For the rest of your exterior scope, see our Windows & Doors service and our Opa-locka coverage page. Homeowners often pair this with Asphalt Driveways & Resurfacing in Opa-locka.
Written by the team at Groundwork Construction Co.