Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Hialeah, FL: What It Costs and How Long It Takes
Metal roofing in Hialeah, FL typically runs $15,000 – $40,000 for a full installation, and most single-story homes are finished in 5 to 10 working days once permits clear. You’re choosing this roof for the long haul: 40-plus years against subtropical sun, hurricane-season wind loads, and the standing-seam panels that meet Miami-Dade product approval. Call (833) 968-1198 and we’ll walk your roofline and put a written range together.
How a Metal Roof Goes On: The Stage-by-Stage Sequence
Metal isn’t a one-day swap. The sequence matters more than the pitch, because half of what makes these roofs hold up in South Florida happens under the panels, not on top of them. Here’s the order we follow.
Stage 1 – Inspection and measurement (day 1)
We get on the roof and measure every plane, valley and penetration, then check the deck and the tie-beam. On 1950s – 1970s concrete-block homes, this is where we learn whether the old roof has a recoverable deck or needs a tear-off. You decide between recovering over the existing roof (cheaper, faster, but stacked layers) and a full tear-off down to the deck.
Stage 2 – Permitting and product approval (days 2 – 10)
Metal roofing in Hialeah needs a permit and a Miami-Dade product approval number for the specific panel and fastening. We handle the submittal, and you choose your panel profile and color in this window so nothing stalls at inspection. Nothing gets ordered until the approval matches the plan.
Stage 3 – Tear-off and deck prep (1 – 2 days)
Old shingles or panels come off, the deck gets inspected and any rotten sheathing replaced, and we install the underlayment and, where specified, a self-adhered waterproof membrane at valleys and penetrations. This is the layer that keeps Hialeah’s summer downpours out of the house.
Stage 4 – Panel installation (3 – 5 days)
Panels go up panel by panel, fastened to spec and sealed at every penetration, ridge and edge. Standing-seam panels are formed to length and clamped, so there are fewer fastener holes than with exposed-fastener panels. You’ll see the roofline come together by mid-week.
Stage 5 – Flashing, trim and final inspection (1 – 2 days)
Ridge caps, gable trim, vents and the ridge vent go on, then the final inspection. We walk the job with you, hand over the warranty paperwork, and make sure gutters and drip edge line up. Only then is the job signed off.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Choose Between
Most of the decisions happen before a single panel is ordered. Here’s the honest trade-off on each.
- Standing-seam panels – the premium choice, hidden fasteners, clean lines, best wind performance. Higher cost, and the panels need room to expand and contract, so flashing detail matters.
- Exposed-fastener (through-fastened) panels – lower cost and quicker to install, but the screws sit on the surface and need checking over the years. A sensible budget option for a shed or a steep back slope.
- Stone-coated steel – looks like tile, weighs far less, and handles wind well. A middle price point and a popular pick where homeowners want a tile look without the weight.
- Aluminum panels – excellent against salt air and humidity, lighter than steel, and a good fit near the coast. Costs more than steel but resists corrosion better.
- Color and finish – factory-coated finishes in a range of colors hold up far better than field painting. This is a look-and-budget call, but it’s worth knowing the finish warranty differs by product.
If your project is part of a full Roofing in Hialeah scope, we lay the metal decision against the rest of the roof plan so the numbers line up.
What Metal Roofing Costs in Hialeah, FL
Plan on $15,000 – $40,000 for a full metal roof installation on a typical Hialeah home. Where you land depends on these variables:
- Roof size and complexity – square footage, hips, valleys and dormers all add panels, labor and waste.
- Tear-off vs. recover – removing old roofing adds disposal and deck-repair cost; recovering saves on the front end but stacks layers.
- Panel type – exposed-fastener is the low end; standing-seam and stone-coated run higher.
- Deck and structure – if the sheathing or tie-beam is soft, repair sits on top of the roofing number.
- Permit scope – Miami-Dade product approval and inspection requirements are part of the job, not an afterthought.
A written, line-item estimate spells out tear-off, underlayment, panels, flashing, trim, permit and disposal, with upfront pricing and no change orders unless you approve them. What it won’t include unless you ask: gutter replacement, skylight work, or structural repairs found under the deck.
See the difference
Before
After
Before
After
Before
AfterWhat Hialeah Homes Specifically Do to This Job
Hialeah isn’t a new-subdivision market. Most of the homes we roof are 1950s – 1970s single-story concrete-block and stucco houses with flat or low-slope roofs, and plenty of them carry converted garages, rear additions and in-law suites built up over decades. That history shows up in the work: low-slope sections need a panel system rated for the pitch, and rear additions built close to the property line in the 33012 and 33010 ZIP codes often need extra flashing detail at the tie-in. Intense summer sun and year-round humidity mean the underlayment and waterproofing have to be right, and hurricane-season wind-load and flood-zone rules mean every panel and fastening carries a Miami-Dade approval. Permitting, inspections and client conversations in this dense, largely Spanish-speaking owner-investor market happen in Spanish, which shapes how we run the job. We also cover Hialeah block by block, from Miami Springs to Opa-locka and West Little River.
Serving Hialeah, FL – Our Local Coverage Area
We serve Hialeah and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Metal Roofing in Hialeah
Most homes are finished in 5 to 10 working days of on-site work, with the permitting window ahead of that. Call (833) 968-1198 for a timeline sized to your roof.
Yes, a metal roof requires a permit and a Miami-Dade product approval for the panel and fastening system. We pull the permit and coordinate the inspections as part of the job.
Sometimes a metal roof can recover over the existing roof if the deck is sound and the layers stay within code limits. Recovering saves cost and time, but a full tear-off is the cleaner choice when the deck is soft or layered. Call (833) 968-1198 for a free estimate.
Metal roof installation in Hialeah runs $15,000 – $40,000, depending on size, panel type, tear-off and deck condition. Call (833) 968-1198 for an exact quote.
Panel finish and manufacturer warranties vary by product, and our workmanship carries the 730-Day Done Right Promise. We hand over the written warranty at final inspection.
Get a Free Metal Roofing Estimate in Hialeah
Call (833) 968-1198 for a free on-site estimate for metal roofing in Hialeah. We’ll measure the roof, check the deck, walk your panel and color options, and leave you with a written, line-item price. That’s part of our Roofing work, and homeowners often pair it with Window Replacement in Hialeah or Impact Windows & Doors in Hialeah while they’re upgrading the envelope. A live person answers around the clock.
Written by the team at Groundwork Construction Co.