Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Opa-locka: What It Costs and What the Job Actually Involves
Vanities, tile and fixtures work in Opa-locka typically runs $9,000 – $28,000 when it’s part of a bath build-out, and most jobs take two to four weeks from demo to final caulk. Call (833) 968-1198 and we’ll walk your room and put real numbers on paper. The scope covers the vanity and counter, floor and wall tile, the shower or tub surround, the toilet, and every trim, valve and finish piece that finishes the room.
The Sequence: How We Run a Vanities, Tile & Fixtures Job
Order matters more than speed here. Tile that goes down before the rough-in is right is tile you pay for twice. Here’s how the stages actually break down.
Stage 1: Walkthrough and written scope (day 1 to 2)
We measure the room, photograph the existing plumbing and electrical, and confirm what stays and what moves. You decide the vanity size and layout, tile direction, and whether the shower valve relocates, because that decision drives the whole rough-in. A written line-item quote comes back with the demo, rough-in, tile and fixtures priced separately so nothing hides in a lump sum.
Stage 2: Demo and substrate prep (days 3 to 5)
Out comes the old vanity, tile, and toilet. We open only what the scope requires. Then we check the substrate: old stucco-and-block walls in Opa-locka homes often need a cement backer board or a waterproof membrane before tile goes up, and wet areas get a bonded waterproofing layer with a pre-slope at the drain. This is where a cheap bid gets expensive later, because skipping the membrane is invisible until water finds the studs.
Stage 3: Rough-in and inspection (days 6 to 9)
Plumbing and electrical get set for the vanity, lights, exhaust fan, and shower valve, then the work is inspected if the scope requires a permit. We don’t open dry areas to close them the same day; the rough-in has to be right first.
Stage 4: Tile and finish (days 10 to 18)
Floor tile, wall tile, and the shower surround go down. You pick grout color and edge profile up front, because a change mid-set means pulling tile. Vanity set, counter, sink, faucet, toilet, trim and accessories follow. Large-format tile takes longer to lay but fewer grout lines to keep clean.
Stage 5: Final walkthrough and punch list (days 19 to 21)
We test every valve, check the caulk lines, seal the grout, and walk the room with you. The work is backed by our 730-Day Done Right Promise, which covers workmanship, not just the first week.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the money and nearly all the regret live in these choices. Here’s the honest read on each.
- Vanity cabinet: Stock cabinets are cheaper and arrive fast; semi-custom fits an awkward Opa-locka bath with a wonky wall far better. Solid wood or plywood boxes outlast particleboard in a humid, wet room. KraftMaid is a solid name here for semi-custom.
- Countertop: Quartz is the default now: no sealing, consistent pattern. Cambria holds up beautifully. Granite is cheaper per foot and needs periodic sealing. Marble looks great and stains easily in a wet bath.
- Floor tile: Porcelain handles moisture and traffic better than ceramic; both are easy to clean. Natural stone needs sealing. Small hex tile suits a period Opa-locka floor; large-format porcelain reads modern and cleans fast.
- Shower wall: Large-format porcelain is low-grout and easy to keep clean; glazed ceramic is cheaper and gives more color options. Either way, a waterproof membrane underneath is non-negotiable.
- Fixtures and finish: Brushed nickel and matte black hold up cosmetically better than polished chrome in a hard-water area. Kohler, Delta, Moen: mid-range finishes give you the same cartridge life as the high-end ones.
- Lighting and vent: A properly sized exhaust fan (sized to the room’s cubic feet) is the single best defense against mold in a humid Florida bath. Dimmable vanity lighting is a cheap upgrade that reads expensive.
What Vanities, Tile & Fixtures Costs in Opa-locka, FL
A vanity, tile and fixtures job in Opa-locka runs $9,000 – $28,000 for a full bath build-out; a vanity-only refresh lands around $800 – $3,000. What pushes a job to the high end:
- Moving plumbing or electrical. Relocating a drain or adding a circuit adds real money; keeping fixtures where they are keeps the number down.
- Substrate condition. Rot behind old tile, out-of-square walls, or a failed pan means demo, repair and re-waterproof before anything new goes in.
- Material grade. Imported porcelain and natural stone, custom cabinets, and premium fixtures climb fast. Stock vanities and builder-grade tile keep you near the low end.
- Room size and tile coverage. Full-height wall tile and a shower surround mean more square footage, more cuts, more labor.
- Permit scope. A cosmetic swap usually doesn’t need one; re-plumbing or moving walls usually does, and the fee becomes part of the bid.
Every written estimate lists what’s covered: demo, permit fees where applicable, substrate prep, membranes, and installation. What’s usually not included is fixture and tile material you buy yourself, surprise structural repair, and mold remediation if old moisture damage turns up mid-demo; we show you that before any extra work starts, not after. Call (833) 968-1198 for an exact quote, and remember the $1,000 off projects over $10,000 and 0% financing for 18 months make a full bath build-out easier to swallow.
See the difference
Before
After
Before
After
Before
AfterWhat Opa-locka Homes Do to This Job
Most of the housing stock here dates to the 1920s through the 1950s: single-family stucco-over-block homes and small apartment buildings, many with original wood-frame windows and flat or low-pitch roofs. That age shows up the moment tile comes off. Behind a 1940s bathroom wall you’ll often find old cast-iron drain lines, missing stud blocking where tile was originally mud-set, and wiring that hasn’t been touched since it was installed. On the Ali Baba Avenue and Sharazad Boulevard blocks with the original six-sided and domed Moorish Revival buildings, walls are load-bearing masonry with decorative parapets and non-standard 1920s framing, and we open any of them only after looking closely enough to confirm nothing structural is hiding. We work the whole city, including the 33054 and 33055 ZIP codes, and if you’re pairing a bath refresh with an exterior job, homeowners often pair this with Tile Roofing in Opa-locka or Specialty Roofing in Opa-locka to knock out two projects at once. Subtropical heat and summer rain make an exhaust fan and impact-rated exterior work smart here, not optional. For a wider scope, this fits neatly into Bathroom Remodeling in Opa-locka or our full Bathroom Remodeling service, and you can see all the areas we cover on our Opa-locka page.
Serving Opa-locka, FL – Our Local Coverage Area
We serve Opa-locka and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Vanities, Tile & Fixtures in Opa-locka
Expect two to four weeks for a full bathroom build-out; a vanity-swap and floor-tile refresh can finish in five to seven days. The timeline stretches if the scope needs a permit or if demo uncovers rot, old wiring, or a failed shower pan. Call (833) 968-1198 and we’ll put a schedule together around your room.
Usually not if you’re keeping fixtures in place and replacing the vanity, tile, and finishes only; the work is considered cosmetic. Re-plumbing drains, adding a circuit, or moving walls typically does require a permit and inspection. We confirm on-site and pull it for you when it’s needed, then walk you through what the building department will look at.
Yes, and it’s the most common way we do it: a new vanity, tile floor and surround, toilet and fixtures set on the existing plumbing saves real money and time. The trade-off is layout constraints, because the shower, drain and toilet stay where they are. We’ll tell you honestly whether the room works better tucked into the existing layout.
A full bath build-out runs $9,000 – $28,000; a vanity-only refresh lands around $800 – $3,000. Substrate repair, plumbing relocation, and material grade move the number most. Call (833) 968-1198 for a line-item estimate, which is free.
Every job we finish is covered by our 730-Day Done Right Promise for workmanship, one of the longest guarantees in the residential construction space. Material warranties from brands like Kohler and KraftMaid stand alongside it. If something isn’t right, we make it right, and our technicians have up to 12 years of experience on installations like these.
Get a Free Vanities, Tile & Fixtures Estimate in Opa-locka
Tell us the room, the vanity you have in mind, and the look you’re after. We’ll walk the space, check the substrate and plumbing, and hand you a written line-item quote for vanities, tile and fixtures in Opa-locka with no surprise add-ons after the fact. Call (833) 968-1198 and a live person picks up, any hour, any day. Every estimate is free, with upfront pricing and the 730-Day Done Right Promise behind it.
Written by the team at Groundwork Construction Co. of Miami.