Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Glenvar Heights: What the Job Actually Involves
Most vanity, tile and fixture updates in Glenvar Heights run $9,000 – $28,000 and take two to four weeks of active work, depending on whether plumbing and electrical move. Small refreshes (one vanity, a floor tile swap, new faucets and lighting without relocating anything) land closer to $4,000 – $9,000. Call (833) 968-1198 for a free on-site estimate before you commit to a number. In a 33143 house with mid-century plumbing, the inspection and prep stage usually decides which end of that range you land on.
How We Sequence Vanities, Tile & Fixtures Work
The order of operations matters more than the finish selection. Get it wrong and you’re re-cutting tile or opening a wall twice. Here’s the sequence we actually run.
Day 1: Demo and Rough-In Inspection
We pull the old vanity, tear out tile down to the substrate, and open the wall behind the vanity if plumbing or electrical is moving. On a 1950s – 1970s Glenvar Heights concrete-block ranch, this is also the day we find out whether the drain and supply lines have survived the last fifty years intact. Older cast-iron and galvanized lines often do not. You’ll know by the end of day 1 what’s about to change scope. This is the single most expensive surprise on any vanity-and-tile job in this ZIP code.
Day 2: Rough-In and Waterproofing
New supply lines, drain relocation, GFCI outlets, and any blocking for a wall-hung vanity go in. Then we waterproof the wet areas. In South Florida’s subtropical climate, tile backer board alone is not enough. We use a bonded membrane over cement board, and pans get pre-sloped and flood-tested before a single tile goes down. That test takes 24 hours and we don’t skip it. If you’re also touching the shower area, this is where scope starts creeping toward a Bathroom Remodeling in Glenvar Heights conversation rather than a vanity swap.
Days 3 – 4: Tile Setting
Floor and wall tile go in, one surface at a time, with cure time between. Large-format porcelain goes down faster than mosaic, but mosaics cover uneven substrates and old floors better. You’ll decide on layout, grout color, and whether you’re doing a full wall or a wainscot. Plan on a full day of setting for a 50-square-foot bath floor, another half day for a tiled shower wall, and grout the following morning.
Day 5: Vanity Set and Fixture Rough
The vanity cabinet sets against the wall, is shimmed and anchored, and the countertop is templated if it’s stone. Faucet, drain, and P-trap get fitted. Lighting and exhaust fan go in. If you’re choosing a stone top, template-to-install is typically five to seven business days, so this is the slack in your schedule, not a delay.
Days 6 – 10: Final Trim, Caulk, and Punch List
Countertop installs, faucet and shower trim finalize, mirrors and hardware go up, and everything gets caulked with a mold-resistant silicone. Then we walk the punch list together, and you don’t sign off until it’s done. Most projects close out in this window unless stone tops or specialty glass are in the plan.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make
- Vanity cabinet: Stock (fast, budget-friendly, standard sizes) vs. semi-custom (KraftMaid and similar lines let you dial width to the inch, which matters in a 1950s bath where nothing is square). Semi-custom adds two to three weeks to lead time.
- Countertop: Cultured marble ($) is forgiving and seamless; quartz or Cambria ($$$) holds up to makeup and heat but costs two to three times more and requires templating.
- Floor tile: Porcelain (durable, low water absorption, best for a wet room) vs. natural stone (travertine, marble – beautiful, needs sealing every 12 – 18 months in Miami humidity) vs. LVT (fast, budget-friendly, but doesn’t tolerate standing water like tile does).
- Wall tile: Full-height tile is the modern standard and the most water-resistant, but it’s the highest tile labor line. Wainscot-to-48-inches keeps cost down and looks period-appropriate in a mid-century ranch.
- Fixtures: Kohler and Moen are the two we specify most, and the trade-off is finish durability vs. price. Brushed nickel and chrome outlast matte black in salt-air environments. Matte black finishes pit faster here than they do inland.
- Exhaust fan: A properly sized, humidity-sensing fan is the single best $150 you’ll spend. Without it, tile grout and paint fail fast in Miami.
What Vanities, Tile & Fixtures Costs in Glenvar Heights, FL
The all-in range for this job in Glenvar Heights is $9,000 – $28,000. Here’s what moves a project to the low end vs. the high end.
- Low end ($9,000 – $13,000): One vanity, floor tile only, fixtures swapped in the same locations, stock cabinet, porcelain tile, cultured marble top, no plumbing moves.
- Mid range ($13,000 – $20,000): Full bath floor and shower wall tile, semi-custom vanity, quartz top, new fixtures, exhaust fan, minor plumbing relocation, GFCI upgrades.
- High end ($20,000 – $28,000): Large or double vanity, full-height tile, stone top, relocated plumbing and electrical, floor leveling over terrazzo, and a permit scope that includes rough-in inspection.
The five variables that push a job up or down: existing condition (cast-iron drain replacement alone can add $1,500 – $4,000), square footage, whether plumbing or electrical relocates, material grade, and permit scope. A written estimate from us itemizes all five. What’s typically not included: structural repairs discovered mid-demo, asbestos abatement in pre-1975 homes, and HOA resubmittal fees.
See the difference
Before
After
Before
After
Before
AfterWhat Glenvar Heights Homes Specifically Do to This Job
33143 sits at the heart of unincorporated Miami-Dade’s most redevelopment-pressured corridor, and that shows up in the work. Mid-century ranch homes along the Palmetto Expressway and US-1 spine are being torn down and rebuilt as two-story customs, so half our tile and vanity jobs are in older houses and half are in brand-new shells where the buyer wants to spec finishes the builder didn’t. Either way, permitting runs through Miami-Dade County, not the City of Miami, and every vanity, tile, and fixture job involving plumbing or electrical needs a permit and rough-in inspection. Because this corridor is under the High-Velocity Hurricane Zone (HVHZ) requirements of the Florida Building Code, out-of-town contractors routinely fail inspections on details that pass elsewhere. New builds also need lot-coverage and setback compliance checked before we touch a wall. Homeowners repiping or re-roofing at the same time often pair this with Tile Roofing in Glenvar Heights or Specialty Roofing in Glenvar Heights to consolidate inspections. If your project is bigger than a vanity-and-tile refresh, our Bathroom Remodeling service covers the full scope, and we work throughout Glenvar Heights and into the neighboring South Miami, Coral Gables, Coral Terrace, and Olympia Heights areas. Impact-rated glazing is standard for anything near a wet wall here, not optional. We schedule interior tile work around the June-to-November storm season when it makes sense.
Serving Glenvar Heights, FL – Our Local Coverage Area
We serve Glenvar Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Vanities, Tile & Fixtures in Glenvar Heights
A typical Glenvar Heights project runs two to four weeks of active work. Add one to two weeks if you’re ordering a stone top or a semi-custom vanity cabinet. Small refreshes (single vanity, floor tile, fixtures) can finish in seven to ten business days. Call (833) 968-1198 for a timeline specific to your space.
Yes, if you’re moving plumbing, adding or relocating electrical, or changing the footprint of a wet area. Pure finish swaps (same-location faucet replacement, tile-over-tile with no plumbing change) usually don’t require one, but Miami-Dade County enforcement varies. We pull permits on every job that needs one, and we walk the rough-in inspection with you. Call (833) 968-1198 to ask about your specific scope.
Yes, and it’s the most common scope we run. Keep the vanity in the same location, tile over the existing substrate with proper prep, and swap fixtures at the same connection points, and your project stays in the $9,000 – $13,000 range. You still get a full visual update. The only catch: if the existing drain is cast iron or the shutoff valves are non-functional, we should replace them while the wall is open, which adds cost but saves you a second demo later.
The range here is $9,000 – $28,000 all in. Vanity alone is $800 – $3,000 depending on stock vs. semi-custom and top material. Floor tile runs $1,500 – $4,500 installed for a standard bath. Fixtures and lighting typically $600 – $2,000. Call (833) 968-1198 for a line-item written quote, estimates are free.
Our workmanship is backed by the 730-Day Done Right Promise: if it’s not done right, we make it right, for two full years. That covers installation defects, tile failures from our work, and fixture installation issues. Material warranties pass through from the manufacturer (Kohler, Cambria, KraftMaid and others). We also offer 0% financing for 18 months and $1,000 off projects over $10,000. Call (833) 968-1198 to talk through the details.
Get a Free Estimate for Vanities, Tile & Fixtures in Glenvar Heights
Call (833) 968-1198 for a free on-site estimate on your vanity, tile and fixture project in Glenvar Heights. A live person answers, 24/7, and we’ll schedule a walk-through that fits your week. On the visit we’ll measure, check the existing plumbing and substrate, and hand you a written line-item quote with the number you see being the number you pay. No surprises, no change-order games. That’s the Groundwork Construction Co. way.
Written by the team at Groundwork Construction Co.