Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Pinewood, FL: What It Costs and How It’s Built
Metal roofing in Pinewood, FL typically runs $15,000 to $40,000 for a full installation, and most homes here are finished in 5 to 10 working days once permits clear. That range covers tear-off, underlayment, panels or standing seam, and trim. What pushes a Pinewood job toward the high end is rarely the metal itself. It’s the wind-uplift engineering, the roof geometry on older concrete-block homes, and whatever we find underneath after 40 years of subtropical sun. Call us at (833) 968-1198 for a free on-site estimate.
How a metal roof goes on a Pinewood home, stage by stage
Metal isn’t a weekend job and we don’t treat it like one. Every stage below has a decision point, and you’ll know what it is before we start.
Stage 1: Inspection and engineering scope (day 1)
We climb up, photograph the deck, and measure the slope and ridge lines. On a 1950s concrete-block ranch, that’s where we confirm whether the existing deck is sound enough for a direct-to-deck panel or whether we’re pulling it back to the framing. You decide which attachment method you want once you’ve seen the photos. This takes half a day.
Stage 2: Permit and product approval (days 2 to 10, before work starts)
Pinewood sits in Miami-Dade’s high-velocity hurricane zone, so the metal system you pick has to carry a Miami-Dade NOA (Notice of Acceptance) or a Florida Product Approval for the design pressure your roof geometry creates. We pull the permit and submit the product approval packet. You don’t have to chase this, but you do have to understand that your material choice is legally tied to the engineering. Changing your mind after submission means a re-review, and we’ll tell you upfront how long that costs in schedule.
Stage 3: Tear-off and deck repair (days 1 to 2 of the build)
The old roof comes off down to the deck. On block-and-stucco homes in 33167, we often find softened fascia or a handful of cracked sheets that were never visible from below. We photograph every one and show you before we touch it. Deck repair gets priced before any metal goes back on, not after.
Stage 4: Underlayment and metal installation (days 3 to 7)
We roll the high-temp underlayment, set the panels or standing-seam pans, and fasten per the approved attachment schedule. For a standard Pinewood hip-and-gable, that’s roughly four to six days of actual panel work. Screw placement, clip spacing, and panel expansion gaps are all set to the engineered spec, and the inspector checks them.
Stage 5: Trim, flashings, and final inspection (final 1 to 2 days)
Ridge caps, valley metal, eave trim, and pipe boots go on, and the whole assembly gets a line-by-line walkthrough with the county inspector. We take a second pass at every fastener and penetration before we call it done. If anything’s off, we fix it before sign-off.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The metal options you’ll choose between in Pinewood
- Standing seam (5/8-inch to 1-inch panels): the top tier for wind resistance. Concealed fasteners, no screw heads to back out, and it holds the highest design pressure ratings. Higher material cost and slower install, but it’s the strongest performer against a Category 3-plus event. This is the benchmark choice for the high-velocity zones.
- Exposed-fastener 5V crimp or corrugated: cheaper per square and faster to install, and it still carries product approval when specified correctly. Trade-off: the exposed screws are the first thing to check after a storm, and every one of them is a potential leak point over time.
- Stamped tile-look panels: popular on Miami-modern homes that want to keep the flat, clean roofline without the weight of barrel tile. Lighter than tile, quicker to install, and it brings a metal system’s wind performance to a house that couldn’t carry actual tile without structural work.
- Galvalume vs pre-painted steel: Galvalume is the bare-metal option and holds up well in salt-adjacent air, but it has a bright metallic look some HOA boards reject. Pre-painted panels in a color match give a more finished appearance and usually come with a manufacturer finish warranty.
- Finish grade: a 24-gauge panel is heavier and stiffer than a 26-gauge and holds its profile better under uplift. On a high-velocity-zone home, the heavier gauge is worth the modest upcharge.
We work with GAF and CertainTeed systems among others, and the specific product approval on the sheet is what matters more than the logo.
What Metal Roofing costs in Pinewood, FL
Plan on $15,000 to $40,000 for a full metal roof on a typical Pinewood single-family home. The line items break down roughly like this:
| Item | Typical range |
|---|---|
| Tear-off and disposal | $1,500 – $4,500 |
| Deck repair and reinforcement | $0 – $4,000 |
| Underlayment and flashing | $1,500 – $3,500 |
| Metal panels, trim, and ridge | $8,000 – $22,000 |
| Labor and permit | $4,000 – $9,000 |
What pushes the number up: a larger or steeper roof plane, standing seam over exposed fastener, a deck that needs reinforcement, more than one chimney or skylight to flash, and any structural work if we find a sagging truss. What keeps it low: simpler roof geometry, a sound deck, standard panel choice, and an existing underlayment that’s still serviceable.
Every estimate we hand you is line-item and written. The number you see is the number you pay unless you approve a change in writing. No surprise additions at the end.
See the difference
Before
After
Before
After
Before
AfterWhat Pinewood homes specifically do to this job
Pinewood is in Miami-Dade’s high-velocity hurricane zone, so metal roofing here is a code-engineering exercise before it’s a materials choice. Every panel system we install has to have a Miami-Dade product approval or Florida Product Approval and a design-pressure rating that matches your roof’s geometry, and the inspector checks the attachment schedule against the approval sheet, not against a generic spec. That’s a review layer most of inland Florida never sees. On the 1950s to 1980s concrete-block and stucco homes that dominate 33167, we’re often working over original decks and old low-slope or flat assemblies, and the retrofitting for wind uplift is the real labor in the job. The blocks near the Little River also sit near a shallow water table and come with floodplain elevation considerations, so staging and site drainage need thought before the dumpster even lands. The June – November storm season governs sequencing too: we plan tear-off and panel-setting around storm watches and afternoon downpours, not around convenience. Pair this with the rest of Roofing in Pinewood if you’re planning an exterior refresh, and homeowners often pair this with Impact Windows & Doors in Pinewood once the envelope is being upgraded for wind.
Serving Pinewood, FL – Our Local Coverage Area
We serve Pinewood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Metal Roofing in Pinewood
A typical Pinewood metal roof takes 5 to 10 working days from tear-off to final inspection, with permit review adding days to weeks before work starts. Storm season can stretch the schedule if a watch interrupts the panel-setting stage. Call (833) 968-1198 for a timeline specific to your address.
Yes. Every metal roof in Pinewood requires a permit and a product-approval submission to Miami-Dade, because the work is in the high-velocity hurricane zone. We pull it and handle the submittal. Call us to walk through what your roof geometry will require.
Almost always yes. Metal can go over the existing geometry, including flat and low-slope roofs, so you keep the home’s existing shape and roofline. The one thing that can change is the deck underneath if we find damage on tear-off. We’ll show you photos before any structural change.
Most Pinewood metal roofs land between $15,000 and $40,000, driven by roof size, panel type, deck condition, and permit scope. Call (833) 968-1198 for a line-item quote on your house; estimates are free.
You get a written manufacturer warranty on the panels and finish plus our 730-Day Done Right Promise on the installation itself. If something we installed isn’t right, we come back and make it right. That’s our commitment to every job.
Get a free metal roof estimate in Pinewood
Call (833) 968-1198 to schedule a free on-site estimate for Metal Roofing in Pinewood, FL. We’ll measure the roof, talk through standing seam versus panel options, and hand you a written line-item quote with the product approval and permit scope included. We serve Pinewood and the surrounding neighborhoods. Calls are answered by a live person, 24/7.
Written by the team at Groundwork Construction Co. of Miami.