Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Opa-locka: What It Costs and How It Works
A tub-to-shower conversion in Opa-locka typically runs $3,500 to $10,000 and takes about 5 to 9 working days from demo to final inspection. The job means pulling the tub and its surround, rebuilding the wet wall waterproofing, setting a shower pan or tile floor, and installing new fixtures and a curb or curbless entry. Most of our Opa-locka conversions land near the middle of that range. Call (833) 968-1198 for a free on-site estimate with a written line-item price.
How a Tub-to-Shower Conversion Actually Unfolds, Stage by Stage
Whether the work goes smoothly depends on the order things happen in. Here’s the sequence we run, and where you’ll be asked to make a decision.
Stage 1: Site protection and demo (day 1)
We mask and plastic off the rest of the bathroom, cut the water, and remove the old tub, surround, and any rotted drywall or backer. You decide then what happens to the removed tub and whether the toilet and vanity stay in place during the work or come out for a cleaner job. This day is the loudest part of the whole process.
Stage 2: Opening the wall and checking the rough-in (day 1 to day 2)
Once the wall is open, we look at the drain, the valve, and the studs. If the existing plumbing can be reused, the conversion stays straightforward. If the drain line needs to shift or the old valve is past its life, we quote that change in writing before touching it. You decide whether to reuse existing plumbing at lower cost or upgrade the valve and drain while the wall is already open.
Stage 3: Waterproofing and backer (day 2 to day 3)
This is where most cheap conversions fail later. We install cement backer, seal the seams, and apply a bonded waterproofing membrane around the pan and walls. You decide on the system here, and we walk you through the trade-offs of a bonded membrane versus a prefab shower surround. Nothing gets tiled until the waterproofing has cured.
Stage 4: Tile, pan, and fixtures (day 3 to day 7)
The shower floor goes in first, then the walls, then the trim and fixtures. Grout and sealant cure for a set period before any water touches the new shower. You’ll pick tile size and layout in the estimate phase so there’s no stopping mid-job.
Stage 5: Final inspection and walkthrough (day 7 to day 9)
If a permit was pulled, the municipal inspector signs off on the plumbing and waterproofing before the job is closed. We test the drain, run the shower, check every joint, and walk you through the finished work. Most jobs are done in under two weeks, and the 730-Day Done Right Promise covers the workmanship long after we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
The look of a converted shower comes from a few decisions made up front. Here’s what most homeowners weigh.
- Prefab acrylic pan and surround: the lowest-cost route, around $1,200 to $2,800 in materials. Fast, easy to clean, and a good match for a rental or a secondary bath. It won’t match a tile look, and it can feel thin underfoot.
- Tile floor and walls over a bonded membrane: the most popular choice in Opa-locka homes. Costs more in labor and time, but you get a custom fit and the look lasts decades if the waterproofing is done right.
- Curb vs. curbless entry: a low curb is the standard and cheapest option. A curbless or zero-threshold shower works better for aging-in-place or mobility needs, but it requires reworking the floor slope and adds plumbing and labor cost.
- Fixtures: we install Delta, American Standard, and Toto valves and trim as standard, with Kohler as an upgrade. A mid-grade valve with a pressure-balance cartridge is the honest sweet spot for most homes.
- Waterproofing system: a bonded sheet or liquid membrane under the tile is the reliable choice. We also use Schluter systems on curbless and tile-heavy jobs where the extra protection is worth it.
- Glass and door: a framed glass door is the budget option; a frameless panel is cleaner-looking but costs more and needs careful measurement.
What Tub-to-Shower Conversion Costs in Opa-locka, FL
The range for this job in Opa-locka is $9,000 to $28,000 for a full bathroom remodel around the shower, and $3,500 to $10,000 for the tub-to-shower conversion itself. A written estimate breaks out materials, labor, permit fees, and any change items so the number you see is the number you pay.
Here’s what pushes a job toward the low end and what moves it toward the high end:
- Size and layout: a standard 5-foot alcove is the cheapest conversion. A larger walk-in or a layout change that shifts plumbing pushes costs up.
- Existing condition: original 1920s or 1950s plumbing and framing often need more work once the wall is open. We quote the surprises in writing before we proceed.
- Plumbing and structure: relocating the drain or valve, or opening the floor for a curbless shower, adds cost.
- Material grade: standard acrylic is at the low end; large-format tile, premium fixtures, and glass add cost.
- Permit scope: if the plumbing moves, a permit and inspection are required and factor into the final price. We pull permits and pass inspections as part of the job.
What’s typically not included: structural repair discovered behind the wall, mold remediation, and upgraded finishes above the agreed scope. We handle change orders in writing so nothing surprises you at the end.
See the difference
Before
After
Before
After
Before
AfterWhat Opa-locka Homes Specifically Do to a Tub-to-Shower Conversion
Opa-locka holds the largest collection of Moorish Revival architecture in the Western Hemisphere, and much of that 1926 fabric sits under homes you might not expect. In the 1920s single-family stucco-over-block houses that make up most of the housing stock here, we regularly find original galvanized plumbing and no modern shower valve, so the conversion often means reworking the valve while the wall is open. The city’s historic character doesn’t usually dictate the inside of a private bathroom, but it does mean careful work around the structure of older homes, and wall cavities that rarely match a modern template.
In the flat and low-pitch 1950s homes common across ZIP codes 33054 and 33055, the moisture load is the real issue: our intense sun and heavy summer rains make a properly sloped pan and sealed waterproofing non-negotiable. Homes along Ali Baba Avenue and Sharazad Boulevard sometimes surprise us with non-standard framing when we open the wall, and any structural change gets engineering review before the shower pan is set. When the shower conversion is part of a larger Bathroom Remodeling in Opa-locka, we plan it that way from the estimate. And when homeowners want the whole house envelope improved at the same time, they often pair a Metal Roofing in Opa-locka or a Tile Roofing in Opa-locka upgrade with the interior renovation, or take on a full Bathroom Remodeling scope. We handle tub-to-shower conversions across Opa-locka and nearby Pinewood, Westview, Hialeah, and Gladeview.
Serving Opa-locka, FL – Our Local Coverage Area
We serve Opa-locka and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Tub-to-Shower Conversion in Opa-locka
Most tub-to-shower conversions take 5 to 9 working days, with demo and waterproofing taking the first three days and tile and fixtures following. That timeline holds when the plumbing and framing don’t need extra work. If a permit inspection is involved, plan for an extra day or two. Call (833) 968-1198 and we’ll give you a date range specific to your bathroom. The estimate is free.
If the plumbing moves, a permit and inspection are usually required. A straight swap of the shower pan and surround on the same drain often doesn’t trigger one, but we confirm with the city before pulling anything. We pull the permits and handle the inspections as part of the job, and the price in your written estimate includes the permit fees.
Yes, in many cases. A standard alcove tub replaced with a same-footprint shower pan keeps the drain and valve where they are and stays on the lower end of the cost range. Curbless showers and layout changes are the jobs that push into the higher range. We tell you which situation your bathroom is in after a free estimate.
Most conversions run about $3,500 to $10,000, and a full bathroom remodel surrounding the shower falls in the $9,000 to $28,000 range. Standard acrylic at $1,200 to $2,800 in materials keeps costs down; tile floors and premium fixtures push toward the top. Call (833) 968-1198 for an exact quote; estimates are free and we’ll put it in writing.
Every tub-to-shower conversion is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right, for two full years after completion. Our technicians have up to 12 years of experience, and the waterproofing details are built to last, backed in writing. The estimate will spell out exactly what the warranty covers.
Get a Free Estimate for Your Opa-locka Conversion
Call (833) 968-1198 to schedule a free on-site estimate for tub-to-shower conversion in Opa-locka. When you call, a live person answers any time, day or night, and we’ll set up a visit to measure your bathroom, check the plumbing and wall condition, and talk through options. You’ll get a written line-item estimate with no surprises, and if you’re weighing a larger bathroom project, we’ll scope it from the start. Ask about 0% financing for 18 months and $1,000 off projects over $10,000.
Written by the team at Groundwork Construction Co.